# interplexmod

## Description

`[`

modulates the input signals `modsignal`

,`efficiency`

] = interplexmod(`signal`

,`ampfactor`

)`signal`

and returns an interplexed signal
`modsignal`

and the power efficiency of the interplexing process
`efficiency`

. The amplification factor `ampfactor`

defines the power distribution between the signals.

For more information, see Interplex Modulation Workflow.

## Examples

### Perform Interplex Modulation of Four Random Signals

Generate four random signals to modulate.

numSignals = 4; x = 2*randi([0 1],1000,numSignals) - 1;

Set the power distribution among the signals to 20%, 20%, 40%, and 20%, respectively.

Calculate the corresponding amplitude factors as the square root of the power distribution of that signal.

ampfactor = [sqrt(0.2) sqrt(0.2) sqrt(0.4) sqrt(0.2)];

Apply interplex modulation to the four signals.

[y,efficiency] = interplexmod(x,ampfactor);

Display the power efficiency of interplexing process.

disp(efficiency)

0.4167

### Perform Interplex Modulation on Three NavIC Signals

Perform interplex modulation on these three Navigation with Indian Constellation (NavIC) signals to generate a complex baseband waveform.

Standard Positioning Service (SPS) signal

Restricted Service (RS) data signal

RS-pilot signal

Set the pseudo-random number (PRN) index for the satellite.

PRNID = 1;

Set the number of navigation data bits in the generated waveform.

numNavDataBits = 3;

NavIC uses course acquisition codes (C/A-codes) for spreading the navigation data spectrum at a chipping rate of 1.023 Mcps.

numCAChipsPerDataBit = 1023*20; randNavICData = 1 - 2*randi([0 1],1,numNavDataBits); caCode = 1 - 2*double(gnssCACode(PRNID,"NavIC L5-SPS")); % Each navigation data bit corresponds to 20 repetitions of C/A-code caBits = repmat(caCode,20,1); SPSsig = caBits.*randNavICData; % Spread SPS data

Generate random data bits for RS-pilot and RS-data signals.

dummyRSP = randi([0 1],numCAChipsPerDataBit*numNavDataBits,1); % RS pilot signal dummyRSD = randi([0 1],numCAChipsPerDataBit*numNavDataBits,1); % RS data signal

Modulate the RS signals by using binary offset carrier (BOC) modulation. Rate-match the SPS signals with the BOC-modulated RS signals.

RSPsig = bocmod(dummyRSP,5,2); RSDsig = bocmod(dummyRSD,5,2); RateMatchedSPSsig = repelem(SPSsig(:),10,1);

Set the amplification factors for the RS-data, SPS, and RS-pilot signals, in that order.

ampfactors = [2/3 sqrt(2)/3 sqrt(2)/3];

Perform interplex modulation of SPS, RS-pilot, and RS-data signals.

[NavICBBWaveform,efficiency] = interplexmod([RSDsig,RateMatchedSPSsig,RSPsig],ampfactors);

Visualize the complex NavIC baseband waveform.

fs = 10*1.023e6; % Sample rate bbscope = spectrumAnalyzer(SampleRate=fs, ... Title="Power spectrum of NavIC signals"); bbscope(NavICBBWaveform)

### Perform Interplex Modulation on Three GPS Signals

Perform interplex modulation on these three Global Positioning System (GPS) signals to generate a complex baseband waveform.

C/A-code

L1 civil (L1C) data ranging code (L1CD)

M-code

Set the PRN index for the satellite.

PRNID = 1;

Set the number of C/A-code navigation data bits in the generated waveform.

numNavDataBits = 1;

Initialize random data for each GPS signal.

```
randLNAVData = randi([0 1],1,numNavDataBits);
% L1CD data bits are twice of C/A-code for same time duration
randCNAV2Data = randi([0 1],1,2*numNavDataBits);
```

Generate a C/A-code for the set PRNID.

caCode = gnssCACode(PRNID,"GPS"); tempCABits = repmat(caCode,20,1); caBits = xor(tempCABits,randLNAVData); rateMatchedCABits = repelem(caBits(:),40); % Rate match with M-code signal caCodeSig = 1 - 2*rateMatchedCABits(:);

Generate L1C-codes for the set PRNID.

l1cd = gpsL1CCodes(PRNID); licdBits = xor(l1cd,randCNAV2Data); l1cdSig = -1*bocmod(licdBits(:),1,1,20);

The spreading code rate for the M-code is 5.115 Mcps, and one bit duration is 20 ms.

numChipsPerDataBit = (5*1023)*20;

Generate random data bits as M-coded data, and then modulate the bits using BOC modulation.

mCode = randi([0,1],numChipsPerDataBit*numNavDataBits,1); mCodeSig = bocmod(mCode,10,5);

Set the amplification factors for the C/A-code, L1CD, and M-code signals, in that order.

ampfactors = [sqrt(0.4) sqrt(0.1) sqrt(0.4)];

Perform interplex modulation of the three GPS signals.

[GPSL1BBWaveform,efficiency] = interplexmod([caCodeSig l1cdSig mCodeSig],ampfactors);

Visualize the complex GPS baseband waveform.

fs = 40*1.023e6; % Sample rate bbscope = spectrumAnalyzer(SampleRate=fs, ... Title="Power spectrum of GPS signals"); bbscope(GPSL1BBWaveform)

## Input Arguments

`signal`

— Input signals

*m*-by-*n* matrix

Input signals, specified as a *m*-by-*n* matrix.
*m* indicates the length of the input signals and
*n* indicates the number of signals to be interplexed.
*n* must be in the range [1, 5].

**Data Types: **`double`

**Complex Number Support: **Yes

`ampfactor`

— Amplification factor

scalar | vector

Amplification factor, specified as one of these options.

Scalar — Use this option to assign the same value to each input signal.

Vector — Use this option to assign an individual value to each input signal. The length of the vector must be equal to the number of columns in

`signal`

.

Amplification factor defines the power distribution between the signals.
`interplexmod`

function internally derives modulation indices
corresponding to each signal using their amplification factors. These modulation indices
are then used to compute `modsignal`

.

For more information, see Interplex Modulation Workflow.

**Data Types: **`double`

## Output Arguments

`modsignal`

— Interplex modulated output signal

column vector

Interplex modulated output signal, returned as a column vector. The length of the
column vector is equal to the number of rows in `signal`

.

**Data Types: **`double`

**Complex Number Support: **Yes

`efficiency`

— Power efficiency of interplexing process

scalar in the range [0, 1]

Power efficiency of the interplexing process, returned as a scalar in the range [0, 1].

Efficiency is computed as total signal power divided by the total transmitted power.

**Data Types: **`double`

## More About

### Interplex Modulation Workflow

This block diagram helps to understand how multiple input signals are modulated by the
`interplexmod`

function.

Here, *theta*_{N} represents the
modulation index and is calculated internally using this formula:

$${\theta}_{N}={\mathrm{tan}}^{-1}\frac{{a}_{N}}{{a}_{1}}$$

where *a* represents the amplification factor.

### Interplex Modulation Equation

The generic interplex equation is given by this formula.

$$s(t)=\sqrt{P}\mathrm{cos}({\omega}_{c}t+\theta (t))$$

where:

*P*is total average power, which is equal to`1`

in this function implementation.*ω*_{c}is the carrier frequency.*θ(t)*is the phase modulation and is calculated as:$$\theta (t)={\theta}_{1}{s}_{1}(t)+{\displaystyle \sum _{n=2}^{N}{\theta}_{1}{s}_{1}(t){s}_{n}(t)}$$

where:

*θ*_{n}is the modulation index.*s*_{n}is square wave of amplitude`1`

.*t*is the instantaneous time.

Considering the above equation, this is the equivalent baseband interplexed signal equation.

$$s(t)=\sqrt{P}(\mathrm{cos}\theta (t)-j\mathrm{sin}\theta (t))$$

## References

[1] Butman, S. and Timor, U.
*Interplex - An efficient Multichannel PSK/PM Telemetry System.* IEEE
Transactions on Communications, 20(3), pp.415-419.

## Extended Capabilities

### C/C++ Code Generation

Generate C and C++ code using MATLAB® Coder™.

## Version History

**Introduced in R2024a**

## See Also

## Comando MATLAB

Hai fatto clic su un collegamento che corrisponde a questo comando MATLAB:

Esegui il comando inserendolo nella finestra di comando MATLAB. I browser web non supportano i comandi MATLAB.

Select a Web Site

Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .

You can also select a web site from the following list:

## How to Get Best Site Performance

Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.

### Americas

- América Latina (Español)
- Canada (English)
- United States (English)

### Europe

- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)

- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)